产品详情

（1） 在洁净的情况下装置轴承：装置场地应与车床、磨床和-机械设备相距一段间隔。场地应清扫洁净，常常坚持枯燥洁净，水分等进入泰州INA轴承。反省轴承箱（座）、轴和轴承的-相关组件以确保其洁净。轴承应留在原有包装中直到装置前的一刻，以避免被污染。

(1) Installation of bearings in clean conditions: The installation site shall be separated by a certain distance from lathes, grinders and other mechanical equipment. The site should be clean and clean, often insisting on dry and clean, moisture into the Taizhou INA bearing. Reflect on the bearing box (seat), shaft and other relevant components of the bearing to ensure its cleanliness. Bearings should be left in the original PACkaging until the moment before the device to avoid contamination.

原则上，牌子不同的润滑脂不能混合，而且，即使是同种增稠剂的润滑脂，也会因添加剂不同相互带来坏影响。

In principle, different brands of grease can not be mixed, and even the same kind of thickener grease, due to the different additives, will have a negative impact on each other.

表面涂有防锈油，您必须用清洁的汽油或煤油仔细清洗，再涂上干净优质或高速高温的润滑油脂方可安装使用。清洁度对泰州INA轴承寿命和振动噪声的影响是非常大的。但我们要特别提醒您的是：全封闭轴承不须清洗加油。

The su-ce is coated with anti-rust oil. You must clean it carefully with clean gasoline or kerosene, and then coat it with clean, high-quality or high-speed and high-temperature grease before installing it. Cleanliness has a great influence on the life and vibration and noise of INA bearings in Taizhou. But we would like to remind you in particular that fully enclosed bearings do not need to be cleaned and refueLED.

此外，已经与油脂密封免维护的所有中，至少有14％的污染只有在所有轴承早期失效的小部分使用轴承显着所致。轴承具有优良的制造和设计能力，能够提供各种恶劣的工作条件密封解决方案。

In addition, at least 14% of all that has been sealed with grease and oil free of maintenance is contaminated only by the use of bearings in a small fraction of all early bearing failures. Bearing has excellent manufacturing and design capabilities, can provide a variety of harsh working conditions sealing solutions.

安装条件是使用因素中的首要因素之一，往往因安装不合适而导致整套轴承各零件之间的受力状态发生变化，轴承在不正常的状态下运转并提早结束使用寿命内在因素主要是指结构设计、制造工艺和材料质量等决定泰州INA轴承质量的三大因素。

Installation condition is one of the most important factors in use, which often leads to the change of stress state among all parts of the whole bearing due to improper installation. The internal factors of abnormal operation and early end of service life of the bearing mainly refer to structural design, manufacturing process and material quality, which determine the INA bearing in Taizhou. Three factors of quality.

1）可以检查对是否加上了意外的载荷和安装误差是否国大等，并成为追究轴承损作原因的线索。

1) It is possible to check whether accidental loads and installation errors have been added, and it can be used as a clue to investigate the causes of bearing damage.

2）轴承安装参数：轴承与轴和轴承座的配合、安装时的偏向等因素也同样对轴承的振动产生影响。

2) Bearing installation parameters: bearing and shaft and bearing seat coordination, installation bias and other factors also have an impact on bearing vibration.

轴承一转动、内圈与外圈的滚道面，由于与滚动体是滚动接触，因而运行轨迹为暗面，运行轨迹附在滚道面上不属于异常，由此变可得知负载条件，所以在拆下万向节轴承的情况下，请严加注意和观察滚道面的运行轨迹。承受大的轴向载荷，承受力矩载荷，或在轴承箱上有极端刚性不均等。

When the bearing rotates, the raceway su-ce of the inner ring and the outer ring is in rolling contact with the rolling body, so the running track is dark, and the running track attached to the raceway su-ce is not abnormal, thus the load condition can be known. Therefore, when the universal joint bearing is removed, please pay close attention to and observe the running track of the raceway su-ce. Bearing large axial load, bearing moment load, or extreme rigidity unequal on the bearing box.

3）轴承工作条件：泰州INA轴承在运转过程中，载荷、转速、润滑条件三个方面对轴承振动的影响最大。

3) Bearing working conditions: In the running process of Taizhou INA bearing, load, speed and lubrication conditions have the greatest impact on bearing vibration.

4）轴承设计参数：包括轴承滚动体数量、套圈壁厚和游隙等。

4) Bearing design parameters: including the number of bearing rollers, ring wall thickness and clearance.

轴承零件的制造误差：包括轴承滚道和滚动体表面粗糙度。大量试验研究表明，波纹度对振动的影响占主导地位，而表面粗糙度和圆度的影响相对较小。

Manufacturing error of bearing parts: including bearing raceway and rolling su-ce roughness. A large number of experimental studies have shown that the effect of Waviness on vibration is dominant, while the effect of su-ce roughness and roundness is relatively small.

文章来自：泰州SKF轴承 www.wh-skf.com

Article from: Taizhou SKF Bearing www.wh-skf.com

文章来自：泰州INA轴承 www.ina-china.cn

Article from: Taizhou INA Bearing www.ina-China.cn

文章来自：泰州NSK轴承 www.klbbearings.com

Article from: Taizhou NSK Bearing www.klbbearings.com

QQ：524085168

电话：0510-81207777

手机：13311666672/13395185757